Capresso Coffee Grinder Replacement Parts: What You Need, When to Replace, and Where to Buy

Is your morning brew tasting flat? Find the right Capresso coffee grinder replacement parts. Learn how to swap burrs and hoppers to save your machine today. 

It’s 6:47 a.m. on a Tuesday. Your Capresso grinder makes a grinding sound—and not the good kind. The motor hesitates. The beans refuse to move. Then, that wrong smell hits you.

Grinders wear out. It is a fact of daily use. But a struggling conical burr grinder is rarely dead. You likely just need Capresso coffee grinder replacement parts. The machines are highly fixable, and new parts are cheap. This guide covers how to spot, source, install, and maintain your coffee grinder parts. Whether you need a complex coffee grinder burr replacement or a simple grinder hopper lid, finding the fix is easy.

If you’re new to Capresso grinders, our Complete Guide to Capresso Coffee Grinder explains the different models, features, and grind settings in more detail.

Why Capresso Grinder Parts Wear Out (And Why It Matters)

Most coffee grinders do not die from bad motors. They fail from worn parts that nobody bothers to replace. Finding the right Capresso coffee grinder replacement parts saves money. You just need to check your Capresso model numbers to get started. Many people buy a whole new machine when a fast fix was all they needed.

High-Use Parts That Degrade Fastest

Every time you brew, internal parts take a beating. Here is what wears out first:

• Burrs (ceramic & steel): These lose their sharp edge after 200 to 500 lbs of coffee.
• Hopper lids: The plastic cracks from heat, UV light, or accidental drops.
• Rubber gaskets: Seals dry out over time. Stale air sneaks in, and flavor suffers right away.
• Ground coffee bin lid clips: These tiny tabs snap under daily pressure.
• Grind selector knobs: Dials loosen up and skip your favorite settings.

Signs You Need Replacement Parts (Not a New Machine)

How do you know it is time for new parts? Watch for these clear signs:

• The grind sounds like gravel in a blender. This points to clear burr damage.
• Your coffee smells off even with fresh beans. Gasket failure is likely the cause.
• Grinds appear uneven. You see fine powder mixed with large chunks.
• The hopper wobbles or does not seal tight against the base.
• The timer or selector no longer clicks into position.

Tracking down Capresso infinity grinder parts takes just minutes online. A quick swap extends the life of your machine by years.

If your grinder won’t start at all, the issue may go beyond worn parts. See “Capresso Coffee Grinder Not Working“ for troubleshooting steps.

Full Parts List for Popular Capresso Grinder Models

Know your machine before buying anything. Your Capresso model numbers are the key to a perfect fit. Parts are not universal across all lines. A catch bin for an older model will not fit a newer one.

Capresso Infinity (Model 560/565) Replacement Parts

This is the workhorse of the Capresso lineup. The most common Capresso infinity grinder parts include the upper and lower burr set. You can also easily find the BPA-free polycarbonate bean hopper, which holds 8.8 ounces. Other available parts include the ground coffee container with lid, rubber sealing gasket, grind selector disc, and country-specific power cords.

If you’re considering replacing major components, read our Capresso Infinity Review to determine whether repairing or upgrading makes more sense.

Capresso Infinity Plus (Model 570) Parts

The Plus model features a few upgrades. You will find an upgraded conical burr set with a stainless steel option. It also uses a larger ground coffee bin. The timer knob assembly is a frequent replacement part. Motor brushes are rare to replace, but third-party sellers do offer them.

Capresso COOL Grind (Blade Grinder) Parts

Blade grinders wear out differently than burr models. You can replace the stainless steel blade assembly directly. The bowl lid features a safety interlock tab that often snaps under pressure. You can also buy a clear, BPA-free grinding bowl replacement or new base rubber foot pads to stop the grinder from sliding on your counter.

Capresso Grind & Brew Parts

Combo machines have unique needs. You can buy a model-specific integrated grinder burr unit. Other parts include the carafe lid and seal, grinder chute cap, and basket filter adapter. Replacing a leaky carafe seal often saves the whole machine.

OEM vs. Aftermarket: Which Replacement Parts Should You Buy?

Not all replacement parts smell like quality. Some aftermarket burrs grind coffee like a blunt axe. I learned this when a cheap blade ruined my morning roast. It left the whole batch tasting flat and burnt.

OEM Capresso Parts — Pros and Cons

OEM parts guarantee a perfect fit every time. They hold exact tolerances. You can buy them directly from Capresso or authorized dealers like Whole Latte Love. The main downside is the price. They usually cost 20 to 40 percent more than aftermarket options. Also, finding OEM parts for discontinued models can be tough.

Aftermarket Parts — What Works, What Doesn’t

For burrs, stick to OEM or known brands. Upmarket blanks from reputable names work fine. For plastic parts like a grinder hopper lid, aftermarket BPA-free options are usually safe. Silicone aftermarket gaskets often outlast original rubber ones. However, always avoid no-brand motor assemblies and unknown blade kits. They are just too risky.

Comparison Table — OEM vs. Aftermarket at a Glance

Part	OEM	Aftermarket
Burr set	Best fit	OK if reputable brand
Hopper	Perfect match	Check BPA-free label
Gaskets	Degrades faster	Silicone lasts longer
Blades	Exact spec	Risky on blade geometry
Price	Higher	15–50% cheaper

Where to Buy Capresso Replacement Parts in the U.S.

One wrong click buys you a part built for European outlets. That mistake will ruin your morning fast. Always double-check your Capresso model numbers before checking out. Finding Capresso coffee grinder replacement parts is easy if you know where to look.

Official and Authorized Sources

Start at the official Capresso website. They offer a direct parts catalog and a handy model lookup tool. Whole Latte Love holds a wide parts inventory with fast U.S. shipping. Seattle Coffee Gear is great for burr sets and accessories. Stores like Williams Sonoma or Sur La Table carry a limited but authentic supply in-store.

Third-Party Marketplaces (Use With Caution)

You can use Amazon, but search by your full model number. Always verify the seller is authorized. eBay is great for old, discontinued parts. Just check that the seller rating is above 98 percent. Walmart.com offers mostly accessories. Compared to Cuisinart or Ninja listings, Capresso items often take more digging to find.

How to Identify the Right Part Number

Check the sticker on your grinder base. It lists the model and serial number. The official parts page uses the number format, like 560.01, rather than the product name. Take a photo of the broken part before ordering. The shape and attachment style really matter. Always cross-reference dimensions for bin fits.

How to Replace the Most Common Capresso Parts (Step-by-Step)

A coffee grinder burr replacement on an Infinity takes under ten minutes. You need zero tools. There are no excuses to put it off.

Replacing Capresso Infinity Burrs

Always unplug the grinder first. Twist the hopper counterclockwise to remove it. Lift the upper burr straight out and note how it sits. Clean the burr housing with a dry brush. Never use water inside the motor area. Drop the new upper burr in and align the tabs. Replace the hopper and plug the machine in. Run a small handful of test beans through it.

The texture should sound like an even, consistent hum. The first batch may carry a slight metallic smell. Discard those grounds and run a second batch.

Replacing the Ground Coffee Bin or Lid

This is a simple snap-fit replacement. You do not need any tools. Just confirm your bin capacity matches. The standard Infinity holds 4 ounces, while the Plus holds 5 ounces. If static cling drives you crazy, look for aftermarket anti-static bins.

Replacing the Hopper (Bean Container)

Check the hopper thread direction before you buy. The Infinity uses a left-hand thread. A BPA-free label should clearly appear on the new packaging. Rinse it with warm water and dry it fully before loading beans. Any leftover moisture equals instant clumping.

Cleaning Before Part Replacement (Reduces Future Wear)

Use Grindz or a rice-alternative cleaner every 30 days. Run a soft brush inside the burr chamber after every five pounds of beans. Wipe the hopper interior weekly. Coffee oils build up and turn rancid. That stale oil will completely ruin your next bag of expensive beans.

Before replacing burrs or other components, it’s worth performing a deep cleaning. Our guide on How to Clean a Capresso Coffee Grinder walks through the process step by step.

Extending Capresso Grinder Life Beyond Parts Replacement

A new burr replacement buys you years. A smart cleaning routine buys you decades. You can often avoid buying parts entirely just by changing how you treat your machine.

Bean Storage Affects Part Wear

Oily beans are tough on grinders. Dark roasts coat your burrs with sticky residue. This shortens their lifespan fast. I left dark roast beans in the hopper over a hot weekend once. By Monday, the oils had seeped deep into the burr housing. Always use an airtight, UV-blocking container for counter storage. Never leave your beans in the hopper overnight.

Grind Setting Habits That Protect Burrs

Never jump straight from a fine espresso grind to a coarse French press setting. Step the dial gradually. If you force a fine grind on a machine rated for coarse, you strain the motor and the burrs. Always run the machine empty between setting changes. This easily clears out trapped coffee grinds.

Using the correct grind setting helps reduce unnecessary wear. See How to Use a Capresso Coffee Grinder for recommended settings by brew method.

How Capresso Compares to Similar Brands on Part Availability

How does Capresso stack up? The Cuisinart DBM-8 offers easy-to-find parts in a similar price range. The Breville BCG820 features expensive OEM parts, but it has better third-party support. The Ninja DGX has far fewer replacement parts available. Its design is not very repair-friendly. Capresso sits right in the middle. You get decent OEM availability and a solid aftermarket ecosystem.

Cost Breakdown — Is Replacing Parts Worth It vs. Buying New?

Replacing the burrs on an Infinity costs about $25. A brand-new Infinity costs $80 to $100. The math is not hard. But sometimes, buying Capresso coffee grinder replacement parts is a bad investment.

Typical Replacement Part Costs (U.S. Market)

Here is what you can expect to pay right now:

• Burr set (Infinity): $18–$35
• Hopper: $12–$20
• Ground bin with lid: $10–$18
• Gasket set: $5–$10
• Full maintenance kit (burrs + hopper + gaskets): $35–$60

When Replacement Stops Making Sense

A dead motor means the repair cost exceeds the machine value. If your model was discontinued over seven years ago, parts get scarce. Quality drops fast. If your grinder cost under $30 brand new, parts often approach or exceed that original value. If multiple parts fail at once, you have systemic wear. It is time to upgrade.

Budget Decision Framework

Use this simple budget rule. If parts cost under 40 percent of a new machine, repair it. If parts cost 40 to 70 percent, weigh your options carefully. If parts cost over 70 percent, buy a new grinder. Consider the Capresso Infinity Plus or step up to a Breville BCG820.

Frequently Asked Questions — Capresso Replacement Parts

Here are real questions from real grinder owners. No fluff, just straight answers.

Are Capresso Infinity Parts Compatible With Infinity Plus?

No. The burr sizes are completely different. The hopper threads do not match. Always confirm your model number before ordering anything.

Are Replacement Hoppers BPA-Free?

OEM Capresso hoppers use BPA-free polycarbonate. They are very safe. If you buy an aftermarket hopper, check the product listing. Look for a clear FDA-approved or BPA-free certification before you buy.

How Often Should Burrs Be Replaced?

For light home use, replace them every three to five years. Light use means one or two cups daily. For heavy use, like brewing a full pot daily, replace them every one to two years. Watch for uneven grind sizes, louder operation, or a flat flavor profile.

Can I Use a Capresso Grinder Part in a Cuisinart or Ninja Grinder?

No. These parts are not cross-compatible. Brands like Ninja, Keurig, and Cuisinart use proprietary dimensions. The thread specs simply will not match up.

Where Can I Find Parts for Discontinued Capresso Models?

Check eBay for used or new-old-stock parts. Try calling Capresso customer service. They sometimes hold stock for seven years after a model ends. Coffee forums like Home-Barista or Reddit are also great resources.

Final Buying Checklist Before You Order Capresso Parts

Use this checklist before you click buy. Guessing leads to returns and wasted time.

Pre-Order Verification Steps

• Confirm the full model number from the base sticker.
• Identify the exact failed part. Take a photo of it.
• Check official OEM sources first.
• Compare aftermarket options. Look for that BPA-free label.
• Verify U.S. voltage compatibility for any electrical parts.
• Read seller reviews. Look for ratings above 4.5 stars and verified purchase notes.
• Check the return policy before you finalize the order.

What to Do After Parts Arrive

Always inspect the box for shipping damage before installing anything. Run a test grind with cheap beans first. Do not waste your good stuff on a test run. Note the date of your replacement. I write it on a piece of tape inside the hopper lid. Finally, schedule a calendar reminder to check your burrs again in 12 months.